Filling In a Swimming Pool: How Much Fill Dirt

To fill in a swimming pool, work out its volume (length x width x average depth in feet, divided by 27, gives cubic yards), then fill it with Spillway Dirt in thin layers, compacting each layer. Ask your city and a pool contractor about permits and the pool shell before any dirt goes in.

Key Takeaways

  • Volume: cubic yards = length x width x average depth (in feet) / 27. A pool is deeper at one end, so average the shallow and deep ends.
  • Spillway Dirt is a silt fill. It packs down when you spread it in thin layers and compact each one, and it settles as you pack it, so order a little extra.
  • It is not screened. Small roots, sticks or debris can turn up in it. Cap it with Premium Garden Soil where grass or plants will grow.
  • Permits, the pool shell and what stays in the ground are questions for your city and a pool contractor, not for a dirt supplier.
  • Building on a filled pool (a house, a shed, a slab) follows an engineer's spec. Spillway Dirt is fill, not structural fill.

Can You Fill In a Swimming Pool With Dirt?

Yes. A pool is a hole, and filling a hole is what Spillway Dirt is for. It is a silt fill, fine-grained with some clay in it, and it compacts when it goes in thin layers.

The dirt is the easy part. Before it arrives, settle what happens to the pool itself.

What Do You Settle Before the Dirt Arrives?

Three questions, and none of them is ours to answer.

Does the city need a permit? Rules differ by city and parish, and filling in a pool can need a permit or an inspection. Call your city or parish permit office before you start.

What happens to the pool shell? Some pools are demolished, some are broken up in place, and the water has to go somewhere first. A pool contractor decides what stays in the ground and how the bottom is opened up.

Will anything be built on top later? If a house, a shed or a slab will sit on the filled pool, ask an engineer. Fill under a building follows the engineer's spec, and Spillway Dirt is not structural fill.

Once those are answered, you know the volume you have to fill.

How Much Fill Dirt Does a Pool Take?

Use the same volume formula as any fill job: length x width x depth in feet, divided by 27. The depth is the part that needs care, because a pool is shallow at one end and deep at the other. Average the two depths.

A 15 x 30 ft pool that is 3.5 ft deep at the shallow end and 7.5 ft deep at the deep end has an average depth of 5.5 ft. 15 x 30 x 5.5 / 27 = about 91.7 cubic yards.

Pool Size Average depth Fill needed
Small rectangle 12 x 24 ft 4 ft ~42.7 cubic yards
Mid-size rectangle 15 x 30 ft 5.5 ft ~91.7 cubic yards
Round 18 ft across 4 ft ~37.7 cubic yards

For a round pool, the area is 3.14 x radius x radius (radius is half the width). For a kidney or free-form pool, split it into rectangles and circles, work out each one, and add them up.

Fill settles as you pack it, so order a little extra. The coverage calculator does the math and rounds up.

To find the fill dirt for a pool, multiply length by width by average depth in feet and divide by 27. A 15 x 30 ft pool that is 3.5 ft deep at one end and 7.5 ft at the other averages 5.5 ft and takes about 91.7 cubic yards.

How Do You Fill It So It Does Not Sink?

Fill the pool in thin layers and compact each one. A hand tamper handles about 1 to 2 inches of loose dirt per pass, and a plate compactor can take 4 to 6 inches (Illinois Extension, 2020). Dumping the whole depth in at once and tamping the top leaves soft ground underneath that settles later, as a dip where the pool was.

Spillway Dirt holds water, so it is not a drainage material. When you reach the top, shape the ground so rain runs away from the house, not toward it. Finished ground should slope at least 4 percent away from the house (Illinois Extension, 2020).

What Goes on Top?

Spillway Dirt is not screened, so it is not the finished top. Where grass or plants will grow, cap it with Premium Garden Soil. For the same job on an ordinary low yard, see how to raise a low yard.

If you are putting sand under an above-ground pool, that is a different job: see how much sand you need.

Where Should the Dirt Be Dropped?

Have it dropped as close to the pool as the truck can safely reach. Every wheelbarrow trip you save makes the job faster. Keep the street and the curb clear of the pile. Our fill dirt delivery page covers the material and the delivery details.

Frequently Asked Questions

What do you fill an inground pool with?

Spillway Dirt, a silt fill, spread in thin layers and compacted. Where grass or plants will grow, cap it with Premium Garden Soil.

How much dirt does it take to fill a swimming pool?

Multiply the pool's length by its width by its average depth in feet, then divide by 27 to get cubic yards. A 12 x 24 ft pool averaging 4 ft deep takes about 42.7 cubic yards. Order a little extra, since fill settles as you pack it.

Do I need a permit to fill in a pool?

Ask your city or parish permit office. Rules differ from place to place, and we do not set them.

Do I have to remove the pool first?

That is a question for a pool contractor and your city. They decide what stays in the ground and how the bottom is opened up.

Can I build on a filled-in pool?

Not on our word. Fill under a house, a shed or a slab follows an engineer's spec. Spillway Dirt is fill, not structural fill.

Get Your Real Delivered Price

You have the volume. The next number is what it costs delivered to your address.

Enter your delivery address on WAYS® and you will see a real instant price on Spillway Dirt, by the yard or the truckload, no quote forms and no callback. We Are Your Supply.

Get your instant delivered price on the WAYS® site

Materials for this job

Sources

  1. Illinois Extension

Related guides

Delivered by city

Spillway Dirt